Exactly How to Set up a Tub
Exactly How to Set up a Tub
Blog Article
Presented here down the page you can get additional high-quality insights all about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Setting up a bath tub isn't exactly rocket science, but it does need strong plumbing, carpentry, and also sometimes, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately tough project. If the old tub is conveniently available, the job can move rapidly; if you need to open a wall surface to remove the old tub and also place the new tub, the job is much harder. In either case, the job is within a residence handyman's skills, although you will certainly need an assistant to leave the old tub as well as embeded in the new one. See to it you have qualified on your own for the job and also are comfortable trying it. As opposed to employing a service provider to take over a halfway-completed job, it is far better to think about utilizing one prior to you start. Possibilities are you might need an expert plumber to make tube links.
This write-up will assist you mount a new tub in your washroom if you have already gotten a new tub as well as do not need to alter the plan of your previous water supply pipes.
Your devices and also product list should consist of the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is detach the water system. After doing so, switch on the faucets to drain pipes any kind of water remaining in the system. The process of removing the existing taps can be fairly bothersome because of the limited access that is typically the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the faucets. Have a cloth prepared for the staying water that will certainly originate from the pipes. Once the supply pipes have actually been gotten rid of, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning throughout this procedure. As soon as the taps have been removed, the holes in the bath/basin will need to be cleansed of any kind of old securing compound.
Before proceeding to fit the new taps, compare the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the thread. One end of the port fits on the plastic tail of the tap and the various other end gives a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, place the tap in the mounting opening in the bath/basin making certain that the washers are in area between the tap and also the sink. Protect the tap in position with the supplier supplied backnut. When the faucet is safely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with typical tap adapters. The former kind ought to be attached to the tap finishes first, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Setting up the Bath tub
Utilizing both wood boards under its feet, place the tub in the required setting. The wood boards are valuable in equally spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto four tiny points.
The following goal is to make sure that the tub is leveled all round. This can be attained by inspecting the level and changing the feet on the bath tub until the level reads level.
To mount taps, fit the bottom of the furthest adaptable faucet connector to the suitable supply pipeline by making a compression join; then do the very same for the other tap.
Activate the water and check all joints as well as brand-new pipework for leakages and tighten them if needed. Load the bathtub as well as also inspect the overflow electrical outlet and the typical electrical outlet for leaks.
Finally, take care of the bath paneling as defined in the supplier's instruction manual. Tiling as well as securing around the bath tub should wait until the tub has actually been made use of at least once as this will settle it right into its last placement.
Preparing for the Installation
First of all, the sustaining structure provided with the bathroom needs to be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to make sure that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps unit to prevent strain on the bathtub.
Fit the versatile tap ports to the bottom of the two faucets utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. See to it you make use of every one of the provided washers.
Link the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath should currently prepare to be fitted in its final position.
Tiling Around the Bath tub
In the area where the bath meets the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the installation can move enough to fracture a stiff seal, triggering the water to penetrate the wall surface between the bath as well as the tiling, resulting in issues with dampness and also feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your fixtures and also fittings. They are sold in tubes as well as cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of soaked paper or soft rope. Remember to constantly fill up the bath tub with water before sealing, to permit the motion experienced when the tub remains in usage. The sealant can fracture relatively early if you do not take into account this activity prior to sealing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily readily available on the market. It is suggested to fit the tiles using waterproof or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
Do you appreciate more info about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Place a remark directly below. We'd be delighted to know your reactions about this article. Hoping to see you back again soon. Make sure you take a moment to distribute this content if you enjoyed reading it. We enjoy reading our article about A Step-by-Step Guide to Installing a Bathtub.
Check Us Out
Report this page